[. . . ] Please don't apply physical pressure to the bezel such as bending or pulling on the bezel.
PNV601
protecting sheet like blanket Do not set the PNV601 on a protection board smaller than itself to avoid the contact with corner of the board. Use a protecting sheet like blanket Do not apply force from the above. [. . . ] are available by attaching the optional expansion board PNZB02.
CONFIDENTIAL
4
Multi Display Setup Manual <Rev1. 0 > September. 30, 2010
Mechanical installation (Remote Control kit)
How to attach Remote Control
CONFIDENTIAL
All monitors can be operated using one remote controller when one of the monitors is fitted with a remote control sensor box
CONFIDENTIAL
5
Multi Display Setup Manual <Rev1. 0 > September. 30, 2010
Setting for Remote Control (1)
Setting for Remote Control kit
CONFIDENTIAL
CONFIDENTIAL
6
Multi Display Setup Manual <Rev1. 0 > September. 30, 2010
Setting for Remote Control (2)
CONFIDENTIAL
CONFIDENTIAL
7
Multi Display Setup Manual <Rev1. 0 > September. 30, 2010
Basic display method (Enlarge or Dot by Dot)
Resolution for Enlarge mode and Dot by Dot configuration
2304
CONFIDENTIAL
Dotbydot mode
1366
Enlarge mode
The enlarge mode in this this configuration won't work because aspect ratio will be different from original the one.
1x3
2732
Create contents with 2304x1366 pixels (or 16:9. 5 aspect ratio under dotbydot)*
2x2
4098
1536
Create contents with 2732x1536 pixels (or 16:9 aspect ratio under dotbydot)*
Enlarge 1920x1080 contents to 2732x1536.
2x3
4098
1536
Create contents with 4098x1536 pixels (or 16:6 aspect ratio under dotbydot)*
The enlarge mode in this this configuration won't work because aspect ratio will be different from original the one.
3x3
Create contents with 4098x2304 pixels (or 16:9 aspect ratio under dotbydot)*
2304 *: When the contents can not be created with dotbydot mode ie. moving picture.
Enlarge 1920x1080 contents to 4098x2304
CONFIDENTIAL
8
Multi Display Setup Manual <Rev1. 0 > September. 30, 2010
Cable routing (for Enlarge mode)
Cable configuration for Enlarge mode
1) DVI Daisy chain
CONFIDENTIAL
2) Other input (HDMI/RGB/Component) and DVI connection in case of more than 6 monitors.
Third monitor and after
Signal Splitter
DVD/BLUE RAY Player
Please refer to the user manual for detailed connection information of the signal splitters.
CONFIDENTIAL
9
Multi Display Setup Manual <Rev1. 0 > September. 30, 2010
Enlarge mode setup
Enlarge mode setup with OSD
CONFIDENTIAL
CONFIDENTIAL
10
Multi Display Setup Manual <Rev1. 0 > September. 30, 2010
Cable routing (for Dot by Dot configuration)
Cabling for Dot by Dot
CONFIDENTIAL
DVI / HDMI
DVI / HDMI Work station Graphic board
DVI / HDMI
DVI / HDMI
Graphic boards which have multiple out put terminals are necessary to realize dot by dot display. Each monitor needs to be connected via DVI or HDMI to a dedicated port on the graphic cards. Multi display setup depends on the type of graphic board and graphics driver.
CONFIDENTIAL
11
Multi Display Setup Manual <Rev1. 0 > September. 30, 2010
Cable routing for monitor control
Cabling (for monitor control)
Three types of connections are available.
1) Connection by RS232C
PNZR01(light receiving device) (1) Control and measuring PC
CONFIDENTIAL
1. Choose RS232C from RS232C/LAN SELECT at the set up page of the all monitors in OSD menu 2. Connect PC (1) and the first monitor with RS232C straight cable (do not use a nullmodem cable) 4. Install monitor calibration tool and the drivers for the measuring device into PC (1).
*If you use the remote control in this configuration, please set PNZR01 (lightreceiving device) to the first monitor. Install monitor calibration tool and the drivers for the measuring device into the PC (1)
*If you use the remote control in this configuration, please set PNZR01 (lightreceiving device) to the first monitor. And you need to make a daisy chain with RS232C straight cables and assign unique IDs as well.
(1) Control and measuring PC
3) Mixed Connection by RS232C and LAN
PNZR01(light receiving device) (1) Control and measuring PC
1. Make daisy chain for all remaining monitors with RS232C straight cable (do not use nullmodem cables) 5. Install monitor calibration tool and the drivers for the measuring device into PC (1).
*If you use the remote control in this configuration, please set PNZR01 (lightreceiving device) to the first monitor. [. . . ] Please take care that the sheet does not extend out of the display side
Gel Sheet Thickness: 0. 5mm
* if you need above tools, please contact delivery agent or our sales reps.
CONFIDENTIAL
23
Multi Display Setup Manual <Rev1. 0 > September. 30, 2010
CONFIDENTIAL
Tools for supporting installation (4)
We will provide following service parts for installation (they are subject to fees)
Name (temporary)
Installation spacer device (UKOG1011MPZZ)
Use
Insert this spacer between the PNV601 while installing the neighboring PNV601s so the units do not touch. And after installation is finished, remove this spacer device.
Image
Temporary stand UKOG1004MPZZ
Temporary stand This stand is for fixing PNV601 temporarily to check operation and perform settings before installation. [. . . ]